Curt Manufacturing 83750 18800 Lb Cap 5/8 In Forged D-Ring W/Bracket Review

Average Reviews:

(More customer reviews)Bought two of these and welded them on the front bolt-on mount of our New Holland tractor yesterday to have some areas to allow us to chain it down better on a trailer. These things are nice and beefy. The mounts you weld on have a notch cut out so you can really get your weld to penetrate both surfaces and give you a solid weld giving you a result of a strongly attached d-ring now on your application. I liked these so much I'm probably going to get two more and attach them to the rear of the tractor since it doesn't have good points to chain down to. I didn't do it, but just make sure that you put your d-ring in the mount before welding it on :D

Click Here to see more reviews about: Curt Manufacturing 83750 18800 Lb Cap 5/8 In Forged D-Ring W/Bracket

Get 2% OFF

Click here for more information about Curt Manufacturing 83750 18800 Lb Cap 5/8 In Forged D-Ring W/Bracket

Read More...

Curt Manufacturing 45824 Tow Strap Ball Mount Review

Average Reviews:

(More customer reviews)This is a very sturdy mount. The bar is a solid piece of steel and the D-ring is thick and solid as well. The towing capacity for this mount will easily exceed any towing rating on a non-commercial vehicle (and probably most commercial vehicles as well). The mounting bar fits snugly in my 2"x2" receiver tube and doesn't rattle around.
I gave it a four-star rating because of the price. At the price I paid at the time of purchase it was more than twice the cost of other similar mounts. Also, I really didn't care for the orange painted D-ring which came all scratched up. I swapped out that D-ring for a silver D-ring and kept the orange one for potential use on a vehicle in need of recovery.
Other similar recovery mounting bars are shorter in length and leaves the D-ring sitting closer to your bumper. This Curt mount bar is a little longer and sticks out a bit from your bumper. I prefer a tighter fit leaving the D-ring sitting closer to my bumper, but others may disagree.
All in all, a great solid recovery mount that should last longer than the life-time factory warranty that covers it.

Click Here to see more reviews about: Curt Manufacturing 45824 Tow Strap Ball Mount

Get 38% OFF

Click here for more information about Curt Manufacturing 45824 Tow Strap Ball Mount

Read More...

1-1/4" Receiver Convert-A-Ball ATV Hitch with 1-7/8" Ball Review

Average Reviews:

(More customer reviews)Fits my 2010 Polaris ATV's factory hitch receiver perfectly, and is exactly what I needed / wanted. It tows my John Deere trailer, drags tarps full of branches / leaves, and can even move light trailers around the yard with it.

Click Here to see more reviews about: 1-1/4" Receiver Convert-A-Ball ATV Hitch with 1-7/8" Ball

Click here for more information about 1-1/4" Receiver Convert-A-Ball ATV Hitch with 1-7/8" Ball

Read More...

WARN 25855 Front Receiver Trailer Hitch, 2 inch Review

Average Reviews:

(More customer reviews)Once you get the bumper off its a snap to install. I would highley recamend.
Thanks

Click Here to see more reviews about: WARN 25855 Front Receiver Trailer Hitch, 2 inch

Get 12% OFF

Click here for more information about WARN 25855 Front Receiver Trailer Hitch, 2 inch

Read More...

Curt Manufacturing 40039 Hitch Ball, 2 5/16 In X 1 In X 2 1/4 In Review

Average Reviews:

(More customer reviews)I was looking for a 2 5/16 Hitch ball, a 1" shank and towing capacity of at least 10,000 lbs. This one is rated at 12,000 lbs. My only complaint is the ball diameter must be at the upper end of tolerance, as it is difficult to connect and disconnect the trailer.

Click Here to see more reviews about: Curt Manufacturing 40039 Hitch Ball, 2 5/16 In X 1 In X 2 1/4 In

Get 42% OFF

Click here for more information about Curt Manufacturing 40039 Hitch Ball, 2 5/16 In X 1 In X 2 1/4 In

Read More...

Master Lock 1465DAT Stainless Steel Barrel Head Hitch Pin Review

Average Reviews:

(More customer reviews)Typical Master Lock quality, but understand it is NOT a lock, just a hitch pin.Anyone can remove it at any time without a tool and with little effort.

Click Here to see more reviews about: Master Lock 1465DAT Stainless Steel Barrel Head Hitch Pin

Click here for more information about Master Lock 1465DAT Stainless Steel Barrel Head Hitch Pin

Read More...

Grip Tri-Ball Trailer Hitch Mount With Tow Hook Review

Average Reviews:

(More customer reviews)I bought this hitch because I got tired of changing balls on my hitch when I went from my boat to the trailer. This seemed like the perfect solution, until I went to use the 2" ball. The hole for the receiver pin is placed too far back on the shaft so I can not use the two inch ball of this hitch.
A simple solution would be to unscrew one and move the 2" to one of the sides I can use but these balls are welded on.
This product does not do what I bought it for.

Click Here to see more reviews about: Grip Tri-Ball Trailer Hitch Mount With Tow Hook

Get 56% OFF

Click here for more information about Grip Tri-Ball Trailer Hitch Mount With Tow Hook

Read More...

Curt Manufacturing 22750 Tube Cover 2" X 2" Black Bulk Review

Average Reviews:

(More customer reviews)There was an unrelated delay in shipping. Otherwise, this cover is what I expected. It fits properly, and keeps dirt and debris out of my front receiver hitch. I'm happy with it.

Click Here to see more reviews about: Curt Manufacturing 22750 Tube Cover 2" X 2" Black Bulk

Get 38% OFF

Click here for more information about Curt Manufacturing 22750 Tube Cover 2" X 2" Black Bulk

Read More...